Tab Content
  • buenijo's Avatar
    03-24-2020, 03:50 PM
    I considered another way to describe some benefits of my system design which might help some to understand my interest. I linked the following video in another thread on this forum. The purpose of my system is fundamentally the same as this "Cobber" system. However, my system is a lot smaller. I estimate the total weight of my system - and this includes the thermal mass and battery system - will come in at approximately 200 pounds and rest on a 1.5' x 4' base. Most of the system will be under 30" in height with the exception of the fuel hopper. My system does this by using a much smaller steam engine system operated at a lower output, then relying on a small thermal mass and battery to meet variable heat and electricity demands. Unfortunately, an inverter is required by my system to provide AC electricity. However, I argue essential electrical loads in the off grid setting should be DC (lighting, electronics are already DC and do not require an inverter generally, pumps, fans, power tools, even a freezer should be DC ideally, etc).
    7 replies | 330 view(s)
  • buenijo's Avatar
    03-24-2020, 03:00 PM
    It is surprisingly simple in design - including the control systems - and very few moving parts. However, the devils are in the details - as you know. In particular, the system absolutely has to operate at a constant low output to make it feasible. This also makes possible a simple steam generator made from 1/4" steel tubing - which is perfectly safe, but also a lot more efficient than traditional boilers. The main headaches I anticipate include the water feed pump, steam admission valve, and the oil separator. These are already designed and parts are sourced. However, those pesky devils are waiting around the corners.
    7 replies | 330 view(s)
  • buenijo's Avatar
    03-24-2020, 02:25 PM
    My thinking at the moment is to use hydronic heating with readily available (and reliable) small DC magnetic drive circulating pumps to distribute hot water to thermostatically controlled DC fan coil units. The unit can be operated without heating the space. I considered this configuration, and determined it would not be difficult. The basic idea is to keep the system operating by providing a heat sink outside the home. This will reduce the thermal mass temperature and keep the system operating. It's a little more involved than this, but not terribly complicated. BTW, everything uses analog controls (with the only exception a readily available and inexpensive voltage sensing relay used as a battery charge controller). This system is designed to be fully serviced by the end user. NOTE: This system makes the most sense for a small remote off grid home in a cold region where wood fuel is readily available. Again, heating applications is the primary purpose. The value of my system is in its ability to provide the same amount of heat from the same amount of wood fuel as compared to any highly efficient wood furnace, but ALSO provide all electricity demanded by the home. If I manage to develop a working prototype that works as designed, then I will consider other subsystems to include (1) water distillation, (2) heat regenerative bulk water pasteurization and filtration, and (3) desiccant evaporative space cooling (the only heat powered space cooling system I have determined can be powered efficiently by this system) - however, I remain convinced the most practical cooling system in the off grid setting is conventional vapor compression a/c units powered as opportunity loads on a PV array.
    7 replies | 330 view(s)
  • buenijo's Avatar
    03-24-2020, 01:39 PM
    Hello acptulsa. The system is designed primarily for heating applications. Rather than using a furnace to directly heat water stored for heating applications, this system heats water to generate high pressure superheated steam used to power a small engine. After moving through the expander, the steam moves to an oil separator and finally a condenser to heat the water stored for heating applications. I did not mention this in the OP, but my design also allows for operating the furnace and heating the thermal mass without operating the engine system. I have good reason to expect the engine system can convert the lower heating value of wood fuel to DC electricity at an efficiency of 8-10%. The design maximum charging rate is 1 KWe. This corresponds to between 5 and 6 pounds of well seasoned wood consumed per KWh of DC electricity. However, the furnace also is designed with a good turndown ratio. So, the system can be adjusted (by the operator) to a lower output if desired. The output is constant once set, and cycles on/off many times each hour to maintain thermal mass temperature. The engine is based on a small single-acting uniflow piston steam engine that operates with superheated steam at medium pressure (300-400 psig and 600-700F) and moderately high speeds (1200 rpm). It is a closed system (fully condensing).
    7 replies | 330 view(s)
  • buenijo's Avatar
    03-24-2020, 12:30 PM
    I started a long term project late last year to design and build a small scale combined heat and power steam engine system fueled by wood (and other biomass fuels). I've been derelict on the project for several months now, and I am just getting back into it. So, I figured I would start a thread to document any worthwhile progress. Please note this is a LONG TERM project that will advance SLOWLY due to limited resources (including both time and money). I do not expect to actually have a test engine operating until some time in 2022 - if at all. PURPOSE: The potential value of this system is in its ability to provide the same amount of heat from the same amount of wood fuel as compared to any highly efficient wood furnace, but ALSO provide all electricity demanded by the home. The primary reasons for selecting a steam system over a wood gas engine system include (1) significantly less fuel processing(*), (2) superior heat recovery, (3) quiet unattended operation. PIC OF TEST FURNACE OPERATING: ***https://www.flickr.com/photos/184818924@N02/48845233148/in/photolist-f6n5E8-f5CVrH-f6bUD5-f6n5Ax-9DNCxB-AdxCX1-xxGhQA-51rBdW-wCZMRy-2biGfxU-wYUAVb-fAUWbW-zYmg7q-wjCASP-wZ9Pd8-xhntVK-xeGFwL-MCfHNc-euvHMR-2hqhA5d-xeffbY-z3qaBL-28C1w6L-wjKryA-tBFqfa-w5Z8aB-2hDmet6-2hYa1B7-2i3397B-7EwkBS-tyxXow-wZbkLF-r85jmE-sh3zub-amRRcg-wkkCBj-ocUDM6*** (*)I tested the furnace with small wood chunks (about 1" across), large wood chunks (about 4" across), small wood splits, and scrap lumber including 3' lengths of 2x4's dropped into the fire tube. It can't seem to tell the difference. However, the wood must be dry. The furnace is the foundation for the entire system, and therefore critical. This crude test unit worked surprisingly well. There was no detectable smoke from the combustion chamber by sight or smell. However, some smoke leaked from the top of the furnace due to poor seals. I estimate the heat output at approximately 10 KW and with peak temperatures approaching 2000F, but I did not get measurements. The basic design of the furnace is sort of a hybrid FEMA gasifier and rocket mass heater. Using a gasifier allows for producing the fuel gas separately. In turn, this makes possible greater control of combustion for higher combustion temperatures, a cleaner burn, and a wider turndown ratio - which I verified by operating the furnace for a long period at a low output (i.e. it still burned hot and clean at the lower output).
    7 replies | 330 view(s)
  • buenijo's Avatar
    03-24-2020, 11:15 AM
    A simple and crude, but fairly high output wood fired monotube steam generator. While not efficient, it shows that a surprisingly simple system can generate steam at a high rate. This unit produced steam at a rate of 3 kg per minute. For reference, Mr. Desai's 6 hp compound steam engine consumes 1 kg of steam per minute at full power.
    224 replies | 76432 view(s)
No More Results

1 Visitor Messages

  1. I began studying politics in 2002 after returning from Afghanistan on active duty military service. I quickly discovered Ron Paul. I started studying economics in 2005. By late 2005 I was buying gold and silver bullion for long term savings. Few individuals today have a clear understanding of economics. What remains of the U.S. Republic is in constant danger of destruction as long as this condition persists. As the inevitable economic collapse continues, the ignorant public will blame what they incorrectly believed to be a "free market" and "capitalism". They will then likely abandon what liberty remains for greater central control.
Showing Visitor Messages 1 to 1 of 1
About buenijo

Basic Information

About buenijo
Biography:
Navy veteran. Degrees in math and physics.
Interests:
Alternative energy. Economics. Political philosophy. Exotic reptiles.
Occupation:
Whatever pays the bills.
Political Campaign Skills
Computer and Technical:
Scientists and Engineer

Signature


“The beginning of wisdom is to call things by their proper name.” - Confucius.
"When plunder becomes a way of life for a group of men living together in society, they create for themselves in the course of time a legal system that authorizes it and a moral code that glorifies it." - Frederic Bastiat
"Being well adjusted to a sick society is not a measure of health." - Jiddu Krishnamurti

Statistics


Total Posts
Total Posts
546
Posts Per Day
0.16
Visitor Messages
Total Messages
1
Most Recent Message
02-06-2011 05:14 PM
General Information
Last Activity
Yesterday 12:26 AM
Join Date
01-01-2011
Referrals
0
No results to display...
No results to display...

06-25-2017


03-21-2016


03-13-2016